Máy ủi Caterpillar D6N LGP

ENGINE - Blow by: Minimal to none
ENGINE - Knocking: No engine knocking
ENGINE - Air cleaners: Good as new
ENGINE - Any smoke: No smoke
ENGINE - Oil or fuel leaks: None visible
ENGINE - General running condition: Runs well
TRANSMISSION - Gear change: Good change, no sharpness
TRANSMISSION - Steering: Responsive
TRANSMISSION - Oil leaks: None visible
TRANSMISSION - Is the transmission noisy?: No
TRANSMISSION - Torque converter: Damper feels good
TRANSMISSION - Controls: Good controls
TRANSMISSION - General running condition: Moves well
UNDERCARRIAGE - Shoe height: 58mm, 90%
UNDERCARRIAGE - Shoes any wear in trailing edge: 90%, Wear minimal
UNDERCARRIAGE - Rail height: 118mm, 70%
UNDERCARRIAGE - Any signs of link failure: No
UNDERCARRIAGE - Average diameter of pins and bushings: 59mm, 70%
UNDERCARRIAGE - Have pins been turned on chains: Yes
UNDERCARRIAGE - Sprockets: 22mm tips, 72mm Gape, 80%
UNDERCARRIAGE - IDLERS - Left side idler: Good as new, 99%
UNDERCARRIAGE - IDLERS - Right side idler: Good as new, 99%
UNDERCARRIAGE - TOP ROLLERS - Left side top roller: 180mm x 180mm, 99%
UNDERCARRIAGE - TOP ROLLERS - Right side top roller: 180mm x 180mm, 99%
UNDERCARRIAGE - BOTTOM ROLLERS - Roller 1: 197mm x 197mm 99%
UNDERCARRIAGE - BOTTOM ROLLERS - Roller 2: 197mm x 197mm 99%
UNDERCARRIAGE - BOTTOM ROLLERS - Roller 3: 197mm x 197mm 99%
UNDERCARRIAGE - BOTTOM ROLLERS - Roller 4: 197mm x 197mm 99%
UNDERCARRIAGE - BOTTOM ROLLERS - Roller 6: 197mm x 197mm 99%
UNDERCARRIAGE - BOTTOM ROLLERS - Roller 7: 197mm x 197mm 99%
UNDERCARRIAGE - BOTTOM ROLLERS - Roller 8: 197mm x 197mm 99%
CAB - Cab Mounts - any wear?: No wear
CAB - Any wiring for laser system?: Yes
CAB - Back up alarm: Loud and clear
CAB - Battery isolator switch: Manual and electric
CAB - Lights: All working
CAB - Wipers: All working
CAB - Heater: Good heat
CAB - A/C: Cold
CAB - Seat condition: Good condition, works as should
CAB - Cladding condition: Average condition
CAB - Floor matt condition: No wear or tears
CAB - Seat belt: Undamaged, working
CAB - Mirrors: Rear view only, undamaged
CAB - Horn: Loud and clear
CAB - Cab glass condition: No cracks or chips
CAB - Any perspex fitted: None
CAB - Steps and grab handles secure: All secure and fitted
BLADE - Blade type: PAT
BLADE - Blade width: 4080mm
BLADE - Blade height: 1280mm
BLADE - Main lift rams wear: L/H: 1mm x 2mm, R/H: 2mm x 2-3mm
BLADE - Pitch ram wear: L/H: 3mm x 5mm, R/H: 3mm x 4mm
BLADE - Tilt ram wear: L/H: 1mm R/H:1mm
BLADE - Link bar wear: L/H: 2mm R/H:2mm
BLADE - C Frame wear: L/H: 2mm, R/H: 3mm
BLADE - Ball joint wear: 12mm
BLADE - Equaliser bar wear: L/H: 3mm, Mid: 1mm, R/H: 4-5mm
BLADE - Face / Moldboard: Good thickness, no dents
BLADE - Spill rack condition: Straight
BLADE - Cutting edges condition: Good as new, 100%
BLADE - Have cutting edges been turned?: No
BLADE - General blade condition: Very decent blade
RIPPER - Ripper valve fitted?: Yes
PAINT & DECALS - Any damage to panels: No damage to panels
PAINT & DECALS - Paint condition: Good
PAINT & DECALS - Condition of decals: To be replaced
VPAT Blade
Drawbar fitted
Ripper valve
Rippers available at an additional cost